Honeywell Voyager 1400g Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 216

Honeywell Voyager 1400g Series Скачать руководство пользователя страница 118

6 - 38

When Check Character is set to

Validate Type 10/11, but Don’t Transmit

,

the unit will only read MSI bar codes printed with the specified type check
character(s), but will not transmit the check character(s) with the scanned
data.

MSI Message Length

Scan the bar codes below to change the message length. Refer to

Message Length Description

(page 6-2) for additional information. Mini-

mum and Maximum lengths = 4-48. Minimum Default = 4, Maximum
Default = 48.

Validate Type 10 and Transmit

* Validate Type 10, but Don’t

Transmit

Validate 2 Type 10 Characters,

but Don’t Transmit

Validate 2 Type 10 Characters

and Transmit

Validate Type 11 then Type 10

Character, but Don’t Transmit

Validate Type 11 then

Type 10 Character and Transmit

Disable MSI Check Characters

Minimum Message Length

Maximum Message Length

«
...
116
117
118
119
120
...
»

Содержание Voyager 1400g Series

























































































































































































































Отзывы:

Нет отзывов