Honeywell VISIONPRO Скачать руководство пользователя страница 23

Страница: 23 / 40

VISIONPRO

IAQ TOTAL HOME COMFORT SYSTEM

68-0287—04

Heat Pump Emergency Heat LED Indication

The thermostat uses a red LED indicator that lights when the

thermostat is in the Emergency Heat mode. The LED is located

in the upper right corner of the thermostat. It is visible only

when on.

Heat Pump Temperature Lockouts

Dual Fuel Heat Pump and Outdoor Temperature
Sensor

In this operation, there is no external fossil fuel kit (dual fuel kit)

installed; the thermostat controls this function.

Choose correct heat pump application in Installer Setup

Number 0172.

Choose

Fossil Fuel Option

as the backup heat source

in Installer Setup Number 0200.

Choose

No External Fossil Fuel Kit Option

is control-

ling back up heat in Installer Setup Number 0210.

Choose

Outdoor Temperature Sensor for Heat Pump

Temperature Lockouts

in Installer Setup Number 0342.

Choose appropriate

Balance Point Temperature

Installer Setup Number 0350.

Dual Fuel Heat Pump Control

Balance Point Only (ISU345 = 0)

NOTE: System must have an outdoor temperature sensor.

When the outdoor temperature is above the selected balance

point temperature, only the compressor operates and the fan

(G terminal) energizes when the thermostat calls for heat. See

Fig. 30. When the outdoor temperature is below the selected

balance point temperature, only the fossil fuel (auxiliary heat)

operates and the fan (G terminal) does not energize when the

thermostat calls for heat.

Fig. 30. Dual Fuel Heat Pump Operation in Heat mode with

Balance Point Set.

Balance Point Plus Droop (ISU345 = 1)

The fossil fuel will turn on when the outdoor temperature is

above the balance point if the room temperature droops below

the selected droop temperature setting, and the compressor

will be disabled.

Balance Point/Auxiliary Heat Lockout Plus Droop
(ISU 345 = 2)

When the outdoor temperature is above the Auxiliary Heat

Lockout Temperature only the compressor operates; below the

balance point temperature (setup function 0360) only the fossil

fuel operates. Between the balance point temperature and

auxiliary heat lockout temperature the compressor will operate.

However, the fossil fuel will turn on if the room temperature

droops below the selected droop temperature setting,

compressor will be disabled.

Fig. 31. Balance Point with Auxiliary Lockout Temperature.

AUXILIARY LOCKOUT FOR ELECTRIC HEAT BACKUP

Heat Pump systems with electric heat backup can select a

compressor lockout temperature (function 0350) and/or

auxiliary heat lockout temperature (function 0360). When the

outdoor temperature is below the compressor lockout

temperature, only the auxiliary heat operates. When the

outdoor temperature is between the compressor and auxiliary

lockout temperatures, both the compressor and auxiliary heat

can operate.

NOTE: System must have an outdoor temperature sensor.

Heat Pump with Electric Auxiliary (Backup) Heat and
Outdoor Temperature Sensor

Choose correct heat pump application in Installer Setup

Number 0172.

Choose Electric as

Auxiliary (Backup) Heat Source

Installer Setup Number 0200.

Choose

Outdoor Temperature Sensor

in Installer

Setup Number 0342.

Choose

Compressor Lockout Temperature

in Installer

Setup Number 0350.

Choose

Auxiliary Lockout Temperature

in Installer

Setup Number 0360.

NOTE: There is a 5°F deadband between the Compressor

and Auxiliary Heat Lockout Temperatures.

Operation in Heat Mode

When the outdoor temperature is below the Compressor

Lockout Temperature, only the Auxiliary Heat operates.

When the outdoor temperature is above the Auxiliary Lockout

Temperature, only the Compressor operates. See Fig. 32.

M22441

BALANCE

POINT

COMPRESSOR ONLY

FOSSIL FUEL ONLY

OUTDOOR TEMPERATURE

OUTDOOR TEMP

ERATURE

BALANCE

POINT

AUX.

LOCKOUT

COMPRESSOR ONLY

COM2 °F

DROOP UPSTAGE TO

FURNACE

FURNACE ONLY

M23497

Содержание VISIONPRO









































Результаты поиска

Содержание VISIONPRO

Отзывы:

Похожие инструкции для VISIONPRO

Бренды по названию

Популярные бренды

Honeywell VISIONPRO, Руководство пользователя

Результаты поиска

Содержание VISIONPRO

Отзывы:

Похожие инструкции для VISIONPRO

Бренды по названию

Популярные бренды