Honeywell VERTEX C Скачать руководство пользователя страница 4

User Manual 

 

 

Symbol 

Description 

 

 

 

Caution: hot surface 

 

 

 

Protective conductor terminal (ground terminal) 

 

EMC Considerations

 

Your Honeywell Analytics continuous gas monitor has been designed to comply with Electromagnetic 
Compatibility (EMC) standards applicable at the time of its manufacturing. The design includes filtering, shielding 
and bypassing techniques. At the time of certification, simulated customer Input/ Output (I/O) schemes were 
tested. 

All methods used in your equipment for emission suppression and reduction of susceptibility are interactive. 
Modifications to the monitor could result in increased emissions and higher vulnerability to other radiated 
fields. 

Following the guidelines in this EMC Considerations section will ensure your monitor maintains the enhanced 
degree of EMC integrity. The guidelines listed apply only to I/O emissions and do not apply to A.C. and D.C. 
monitor power connections. 

 

FCC Compliance Statement

 

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation. 

 
 
NCC Compliance Statement

 

取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率
或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有
干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前述合法通信,指依電信管理法規定
作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之
干擾。

 

 

Without permission granted by the NCC, any company, enterprise, or user is not allowed to change 
frequency, enhance transmitting power or alter original characteristic as well as performance to an 
approved low power radio-frequency devices. The low power radio-frequency devices shall not influence 
aircraft security and interfere legal communications; If found, the user shall cease operating immediately 
until no interference is achieved. The said legal communications means radio communications is 
operated in compliance with the Telecommunications Management Act. The low power radio-frequency 

Содержание VERTEX C













Отзывы: