Honeywell Thor VM3 Скачать руководство пользователя страница 310

Страница: 310 / 378

298

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

VMXD Enhanced Dock

Caution: This dock is designed for DC power vehicle-mounted

applications only.

SKUs

VMX004VMCRADLE

Power Connector

6-pin connector:
13.2VDC input power; requires DC power supply
Connector is also used for screen blanking via COM1 CTS and RTS signals

COM1Connector

9-pin male, RS-232 serial port, COM1 with switchable power on pin 9
Do not use COM1 when screen blanking box is attached to avoid port conflicts.

COM2 Connector

9-pin male, RS-232 serial port, COM2 with switchable power on pin 9

CANBUS/AUDIO Connector

15-pin male, CANbus/Audio connector supports either audio/microphone via adapter cable or
J1939 Female and J1939 Male connectors via CANbus cable

USB1 Connector

9-pin female, USB connector supports USB host port via adapter cable

Note:

USB Client port may not be supported by the Thor VM3 operating system.

USB 2 Connector

15-pin female, USB connector supports 2 USB host ports via adapter cable

USB2 Connector

15-pin female, USB connector supports two USB host ports via adapter cable

USB 2 Connector

15-pin female, USB connector supports 2 USB host ports via adapter cable

USB Host Connector

One USB Host connector behind waterproof cap

Ethernet

One RJ45 Ethernet connector behind waterproof cap

Power Switch

Sealed power switch

External Power Supply

AC Adapter, 120-240VAC to 12VDC

Input Power

DC Input Voltage: 13.2VDC,
Input Current: 4.6 Amps (typical),
Input Fuse: 8A Time Delay. Replace with same size, rating and type of fuse:

•

Littelfuse 0215008.MXP

•

Cooper Bussmann BK1/S506-8-R

•

Bel Fuse 5HT 8-R

or equivalent.

External Power Supply

50-150 VDC DC power supply required for all installations

Note:

Use dock VMX005VMCRADLE (VMXD Enhanced Dock of Off-Vehicle Use) in AC power
applications.

Содержание Thor VM3



























































































































































































































































































































































































Результаты поиска

Содержание Thor VM3

Отзывы:

Honeywell Thor VM3, Руководство пользователя, Страница: 310 / 378

Результаты поиска

Содержание Thor VM3

Отзывы: