Honeywell T320 Скачать руководство пользователя страница 55

Страница: 55 / 97

Chapter 5 - Servicing

Slot number

Description

Option

Slot 2

PCIe_G2x1

Slot 3

PCIe_G3 x16 _CPU1

LCNP4e/LCNP4e2

Slot 4

PCIe_G3x4_CPU1

Slot 5

PCIe_G3x16_CPU2

Not Populated

Slot 6

PCIe_G3x4_CPU1

Empty for MZ-PCSV71

PERC H310 Controller for MZ-PCSV72

PERC H710 Controller for MZ-PCSV73

NOTE

A Local Control Network Processor (LCNP) board and LCN Media Access Unit (MAU) are no
longer used if the Server has been upgraded to be an ELCN node.

5.5.2

Slot requirements for General Ethernet and FTE node setup

The following table identifies the specific slots for each of the Honeywell options for general Ethernet
and FTE node configurations.

Configuration

PCIE-
x 4

PCIE-
x 8

PCIE-
x 4

PCIE-x 4

FTE Supervisory (Default)

Free
Slot

Empty for MZ-
PCSV71

PERC H310
Controller for MZ-
PCSV72

PERC H710
Controller for MZ-
PCSV73

1 NIC, Standard Ethernet
through one on-board NIC

Free
Slot

Empty for MZ-
PCSV71

PERC H310
Controller for MZ-
PCSV72

PERC H710
Controller for MZ-
PCSV73

2 NICs, Standard Ethernet

Free

Empty for MZ-

- 55 -

Содержание T320


































































































Результаты поиска

Содержание T320

Отзывы:

Бренды по названию

Популярные бренды

Honeywell T320, Планирование, установка и руководство по обслуживанию

Результаты поиска

Содержание T320

Отзывы:

Бренды по названию

Популярные бренды