Honeywell SUITEPRO TB6575 Скачать руководство пользователя страница 2

TB6575/TB8575 DIGITAL FAN COIL THERMOSTATS

62-0311—05

2

SPECIFICATIONS

Supply Voltages:

TB6575A1000 and TB6575B1000:

120 Vac ±10% at 50/60Hz

240 Vac ±10% at 50/60Hz

TB8575A1000:

20 to 30 Vac at 50/60Hz (using 24 Vac, Class 2, 

NEMA rated transformer)

Safety Fuse:  

15 A, 250 Vac. If the safety fuse blows, the 

thermostat must be replaced. The fuse is not field 
replaceable.

Electrical Ratings:  

(see Table 1).

Environmental Ratings:

Temperature:

Operating Range: 18°C to 49°C (0°F to 120°F).

Shipping and Storage Range: -29°C to 49°C (-20°F to 

120°F). 

Humidity:

 5% to 90% RH, non-condensing.

Onboard Temperature Sensor: 

Type: 10K NTC
Working Range: 18°C to 49°C (0°F to 120°F)
Display Range: 0°C to 37°C (32°F to 99°F)
Accuracy ±2.0°F at 70°F

Remote Temperature Sensor (

optional

):

Type: 20K NTC
Working Range: 18°C to 49°C (0°F to 120°F)
Display Range: 0°C to 37°C (32°F to 99°F)
Accuracy ±2.0°F at 70°F

Remote Pipe Sensor (

optional

):

Type: 20K NTC
Working Range: 0°C to 93°C (32°F to 199°F)
Display Range: 0°C to 93°C (32°F to 199°F)
Accuracy ±5.0°F over the temperature sensing range

Remote Setback Input: 

Dry contact, maximum 

resistance of 100 ohms. TB6575 – 9Vdc, < 4 mA; TB8575 
– 16 Vdc, < 5 mA. Note Electrical WARNING on page 3.

Remote Setback Range:

Heating: 10°C to 21°C (50°F to 70°F).
Cooling: 22°C to 32°C (72°F to 90°F).

Enclosure: 

Plastic (cover, sub-base, and optional adap-

tor plate) 

Junction Box Mounting: 

Direct mounting on a horizontal 

single gang NEMA 2 x 4 in. surface mount electrical box, 
or on 4 x 4 in. box or vertical 2 x 4 in. surface mount 
electrical box with the optional 50033847-001 adapter 
plate.

Dimensions: 

See Fig. 1 on page 3.

Wiring: 

11 screw-in terminals located on the sub-base 

capable of accepting up to 2 x 18 AWG (0.8 sq. mm), 1 x 
16 AWG (1.3 sq. mm), or 1 x 14 AWG (2.1 sq. mm) wires. 
Accepts stranded or unstranded 14-28 gauge wire.

NOTES:

1. The TB6575A1000 model is pre-fitted with color-

coded fly leads (16 AWG) attached to seven 
terminals.

2. The TB6575B1000 model is pre-fitted with color-

coded fly leads (16 AWG) attached to six 
terminals.

3. The TB8575A1000 model does not have fly 

leads attached to any terminals. 

4. See Table 3 on page 5 for fly lead usage.

Minimum Operational Life (at maximum load):

Thermostat contacts: 100,000 cycles

Approvals:

CSA Certified C/US for Canada and the U.S.A. Meets 

the same requirements as UL-873.

FCC Part 15 Class B

Accessories:

• 50033847-001 – Adapter plate for mounting on a 

vertical 2 x 4 in. single-gang or double-gang NEMA 
standard vertical switch box (6 1/4 in. (158 mm) x 5 1/
16 in. (128 mm) x 13/22 in. (10 mm)).

• TR21 – 20K Ohm NTC Non-Linear Remote 

temperature sensor.
Other acceptable remote temperature sensors are —

• 20K Ohm: C7041B2005, C7041B2013, C7041C2003, 

C7041P2004, C7770A1006, C7772A1004, and 

C7772A1012

• 10K Ohm (for averaging only): TR21-A

• PS20 – Remote pipe sensor (20K Ohm)
• W6380B1005 – Fan Coil Unit Relay Control Center
• WSK-24 - Wireless Occupancy Solution (Receiver, 

occupancy sensor and door sensor)

Models, applications, and features:

Table 2 identifies the applications and features of each 
model.

Table 2. Applications and Features

Table 1. Electrical Ratings.

Component

Amps (inductive) for:

24 Vac

120 Vac

240 Vac

Fan Relay

1.0 A

6.0 A

3.0 A

Heat/Cool Relay

1.0 A

1.0 A

1.0 A

Models

Applications

Features

Heat/Cool/
Auto

Pipes Voltage

Number
of Relays

a

Energy
Savings
Input

Fan: On, 
Auto, or 
3 speed

Manual/
Auto
Changeover

Remote
Sensor

Back
 Light

Pipe
Sensor

b

TB6575A1000 All

2 or 4 120 or 

240 Vac

5

Yes

Yes

Yes

Yes

Yes

Yes

TB6575B1000 Heat or 

Cool

2

120  or 
240 Vac

4

TB8575A1000 All

2 or 4 24 Vac

5

Содержание SUITEPRO TB6575





















Отзывы: