manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 473 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 473

SmartPAC 2 with WPC Integration

1126800

SmartPAC Preventive Maintenance

Appendix B

page 451

(PM) Monitor

Viewing and modifying PM Alerts

1. Select "PM Monitor" from the first display in Run mode.
2. You will see the list of PM items that you previously assigned in the Initialization status.

The first item is highlighted in the next example.  Use the cursor keys to view the other
items on the schedule.  Currently the PM status for all items is "normal" (see display).
This means that none of the items have reached the limits set in Initialization.

USE CURSOR KEYS TO CHANGE SELECTION
PRESS ENTER TO SELECT, RESET WHEN DONE

CLUTCH VALVE
   ALERT AT
   CURRENT

2000 STARTS/STOPS
1001 STARTS/STOPS

YOUR PRESS NAME
STATUS IS NORMAL

PM MONITOR

SLIDE ADJ. MOTOR
    ALERT AT
    CURRENT

100 DIE CHANGES
  75 DIE CHANGES

GIBS
   ALERT AT
   CURRENT

1000000 STROKES

458239 STROKES

MORE

notice that alert status
is "normal"

CLEAR

ALERT

F3

CHANGE

VALUE

F4

Figure B - 15.  Display Showing PM Monitor in "Normal" Status Mode

NOTICE

You may notice that some of the current values do not update on every stroke while the
press is running.  SmartPAC is keeping track of these items, but does not refresh the display
until the press actually stops.

3. The next display shows that one of the items, "Slide Adjust Motor" is now in "alert"

status mode.  It flashes on the screen.  Also, the number of items in alert status mode
appears at the top of the screen.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов