manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 438 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 438

1126800 

SmartPAC 2 with WPC Integration

Page 416

Chapter 7

SmartPAC 2 Fault Messages

Fault message for red sensors  "This N/C sensor is open"

Explanation:

A red sensor has actuated (is open to ground). When this message appears,
the angle where the condition was detected is also listed shown on the
LCD display.

Remedy:

   Check for the press or equipment malfunction that the sensor was

supposed to detect. If none has occurred, check for a malfunctioning
sensor. Check for loose or detached wiring at the remote connection box
or controller. Check for a severed wire from the sensor to the RCB or
controller.

Miscellaneous Fault messages

"Maximum press speed exceeded"

Explanation:

This message is generated when the press is running at a speed greater
than the maximum limit set at SmartPAC 2.

Remedy:

After clearing the error, either run the press at a slower speed, or adjust the
maximum limit set at SmartPAC 2.  Refer to Chapter 4.

"Minimum press speed exceeded"

Explanation:

This message is generated when the press is running at a speed less than
the minimum limit set at SmartPAC 2.

Remedy:

After clearing the error, either run the press at a higher speed, or adjust the
minimum limit set at SmartPAC 2.  Refer to Chapter 4.

"stop"

Explanation:

This message is only generated when SmartPAC 2 is communicating with
PACNet Computerized Pressroom Reporting software.

  The user at the

computer has sent a top stop command to that SmartPAC 2.  When this
occurs, SmartPAC 2 in turn stops the press.

Remedy:

   Because this condition was generated by someone at the computer, it is

important to investigate the reason why the stop command was issued.  A
problem may be present.  Check with personnel before proceeding.  After
the situation is clear, press RESET to continue.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов