manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 427 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 427

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Fault Messages

Chapter 7

page 405

DSV Interface and Lockout relay failures

70*  through  76*

Problem:

These errors indicate failures that have occurred in the DSV interface.
Note that #72 through #76 can also be generated by the second processor.
The errors are as follows:  

F70

The first (DSV-A) DSV relay driver did not open at start of stroke

F71

The two DSV relay drivers have shorted together

F72 or H72

The DSV control flip-flop not functioning properly

F73 or H73

The DSV missing pulse detector window not functioning properly

F74 or H74

The DSV relay driver did not close properly at the start of the stroke

F75 or H75

The DSV relay driver did not open properly at the end of the stroke

F76 or H76

The Lockout relay driver did not open properly at the end of the stroke

F77 or H77

The Lockout relay check contacts were not closed before the lockout relay
was turned on.  Check fuse F402 on the WPC power supply board.

Remedy:

Reset.  If you still get these errors, contact Wintriss Tech Support for
assistance or replacement.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов