manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 424 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 424

1126800 

SmartPAC 2 with WPC Integration

Page 402

Chapter 7

SmartPAC 2 Fault Messages

50

Problem:

This error applies to cross-checked user input pair 8 & 9.  It occurs if one
or both of the inputs are open.

Remedy:

Check the auxiliary equipment that signaled the stop.  Correct the
problem.  Reset SmartPAC.  If the error does not go away, contact
Wintriss Tech Support for assistance.

58

Problem:

This error applies to cross-checked user input pair 10 & 11.  It occurs if
one or both of the inputs are open.

Remedy:

Check the auxiliary equipment that signaled the stop.  Correct the
problem.  Reset SmartPAC.  If the error does not go away, contact
Wintriss Tech Support for assistance.

Light Curtain faults

60  or  61

Problem:

These errors indicate that the light curtain(s) failed the internal light
curtain test conducted by WPC.  There may be a problem with the wiring
of either the first or second light curtain connected to WPC (#60 applies to
the first, #61 applies to the second).  This error can also be generated by
the second processor.

Remedy:

Check that your light curtain wiring is correct.  Refer to Chapter 2 either in this

manual in the light curtain user manual.  If you need more assistance,
contact Wintriss Tech Support.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов