manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 421 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 421

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Fault Messages

Chapter 7

page 399

Component failures

47  through  48

Problem:

These errors indicate failures that have occurred to standard equipment
connected to WPC.  If "47" occurs, possibly dirt or water has gotten into
the DSV.  You may need to rebuild the valve.  Regarding "48,”  the air
pressure may be turned off or set too low.  If you are using the Air
Pressure sensor instead of the Air Pressure switch, "48" will occur if you
have not wired terminal #8 to ground (see Chapter 2).

F47

Dual Safety Valve (DSV) monitor switch input open

F48

Main system air pressure switch input open

Remedy:

Reset and correct the problem.  If the errors persist, contact Wintriss Tech
Support for assistance.

  

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов