manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 383 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 383

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 361

MESSAGING

(RUN – MESSAGING)

NOTICE

Find instructions for running the press at the end of this chapter, starting on page 364.

This choice shows on the menu if you have enabled e-mail in Initialization mode (see page
259).  If your SmartPAC 2 is connected to a computer network, you can choose to have it
send e-mail messages.

Before using the e-mail messaging function, you must set up the e-mail recipients and
messages using SmartView remote viewing utility. (See  “Appendix D – SmartView,” page
455.)

1.

 

In the main Run menu, select MESSAGING.  A screen appears similar to the following,
which lists the recipients you have set up using SmartView.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 29.  E-mail, Select Recipient

2.

 

Use the cursor keys to highlight the recipient you want to send a message.  Press 

F3

-

“Select Recipient.”  The recipient’s name appears next to “To:” at the top of the screen.
You can select more recipients in the same way if you want.

3.

 

Press 

F4

-“Select Message.”  A screen appears similar to the following:

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов