Honeywell SmartPAC 2 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 37

SmartPAC 2 with WPC Integration

1126800

Introduction to SmartPAC 2

Chapter 1

page 15

Green Quick Check

A sensor input set to "green quick check" is almost the same as the "green" setting. The
sensor must turn on at least momentarily within the ready signal. However, a green quick
check sensor

cannot stay on or turn on

outside the ready signal. The sensor must turn on,

then turn off within the ready signal. Otherwise, SmartPAC 2 sends the stop signal to the
press.

KEY

= Ready

Signal

Green

Quick Check

Sensor

not allowed

(press stops)

Sensor never goes
ON.

Stop signal sent at
end of ready signal.

TDC

BDC

OK

Sensor goes ON
only inside ready
signal.

TDC

BDC

Sensor is ON outside ready signal.

Stop signal sent when sensor is ON outside ready
signal.

not allowed

(press stops)

TDC

BDC

TDC

BDC

TDC

BDC

= Sensor

ON

Figure 1 - 4. How SmartPAC 2 Interprets Signals From a Sensor Set to

"Green Quick Check"

«
...
35
36
37
38
39
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов