manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 336 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 336

1126800 

SmartPAC 2 with WPC Integration

page 314

Chapter 5

SmartPAC 2 Program Mode

PRESS CONTROL

(PROGRAM – PRESS CONTROL)

If you have a variable speed press, you can program different speed limits for different tools.
Select  "Press Control" from the main Programming menu, Figure 5 - 3. .

 

ENTER YOUR PASSWORD

USE THE  KEYPAD TO ENTER NUMBERS.
USE THE UP/DOWN CURSON KEYS TO
INCREASE/DECREASE. PRESS ENTER
WHEN DONE. PRESS RESET TO CANCEL.

    60599

If this display appears, you need to enter the general password to access these settings.  Password

access is set under Security Access in Initialization mode.  See “Security Access” in
Chapter 4, page 251.

A display similar to the following appears:

Figure 5 - 38.  Press Control Parameters

These items enable you to set the top stop angle, counterbalance setpoint and press operating
speeds for this tool.  Select the item you want to change, key in the value with the numeric
keys and press ENTER.  Press RESET when you are done with this screen.

NOTICE

If you have installed a keylock switch to prevent changes to WPC settings, this screen may
show this notice:  “THE PRESS CONTROL EDIT MODE IS LOCKED.”  See “Additional
Security,” page 257.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов