manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 28 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 28

1126800 

SmartPAC 2 with WPC Integration

Page 6

Chapter 1

Introduction to SmartPAC 2

•

TOP STOP switch

, which stops the ram at the top of stroke during continuous

operation.

•

LEFT/RIGHT SELECT key switch

 for the ONE HAND trip mode, which is

located on the bottom of the Operator Station (optional).

OPERATOR STATION

PRIOR ACT

switch

PALM TIME

LED

MUTE

LED

TOP STOP

switch

EMERGENCY STOP /

RESET

switch

RUN / INCH

palm switches

RUN/

INCH

RUN/

INCH

EMERGENCY

STOP

RESET

PALM

TIME

PRIOR

ACT

MUTE

TOP

STOP

Figure 1 - 2.  Illustration of Operator Station

•

Dual-monitored Safety Valve

, which controls the air flow that operates the clutch and

brake of the press.  DSVs are available in many popular sizes.

•

System air pressure switches

, which monitor the system air pressure.

•

Shadow light curtain

: The Shadow light curtain is a presence-sensing device that places

an infrared light field between the point-of-operation and the operator. When something
enters the sensing field and a light beam is blocked, the object is detected and the press is
immediately stopped.

The standard WPC package is designed to be used with a Shadow light curtain. However,
you can purchase WPC without a light curtain. In this version, the control enclosure does
not have a MODE SELECT switch, and WPC will only operate in the TWO HAND
mode.

Shadow light curtain is optional for two-hand mode, but is required for point-of-operation
guarding if WPC is used with a foot switch or in the one-hand mode. WPC tests up to
two Shadow inputs every time the press is started and stopped.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов