manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 253 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 253

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 231

USE THE CURSOR KEYS
TO MAKE SELECTIONS.
PRESS ENTER TO
ACCESS SELECTION.

TOOL NUMBER 1234567        PART CNTR        0
CHAIR BRACKET
SENSORS ENABLED

DISABLE SENSORS
COUNTERS

BRAKE MONITOR

DIE PROTECTION
CAM SWITCH
TOOL INFORMATION
ERROR LOG
LOAD NEW TOOL

BRAKE MONITOR

Figure 4 - 26.  Selecting "Brake Monitor" from SmartPAC's Run Menu

3. Start the press. Run it in continuous mode, allowing it to reach normal operating speed.

Notice now that the actual press speed -- "SPM" -- automatically appears on the display.

4. Top stop the press.  Look at the reading in the display. This is the stopping time of your press.

Note:  The number in the display is in milliseconds (ms).

5. Do this test at least 5 more times. Record the highest reading from all your tests. This is

the stopping time you will use to calculate and set the Stop Time Limit.

STOP TIME
START TIME
STOP ANGLE
90 STOP

300
200

75

PRESS THE UP CURSOR KEY TO START THE
90 DEGREE BRAKE TEST.
PRESS THE RESET KEY WHEN DONE.

STOP TIME STATUS

TOOL NUMBER 1234567        PART CNTR        0
CHAIR BRACKET
SENSORS ENABLED

250
155

75

0

LIMIT (MSEC)

VALUE (MSEC)

Figure 4 - 27.  Viewing "Stop Time" in Run Mode

Calculating the Press's Stop Time Limit

After you know the press's actual stopping time, you need to add extra time to this number to
compensate for 

normal 

wear in your brake. Otherwise, WPC would stop the press as soon as

the stopping time increased just slightly. This extra time is referred to as "Tbm." The

minimum value that you can set is 10 ms. The stopping time plus Tbm will be the stop time
limit setting.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов