manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 208 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 208

1126800 

SmartPAC 2 with WPC Integration

Page 186

Chapter 3

SmartPAC 2 Keyboard, Displays

and Operating Modes

SmartPAC 2 Display

PRESS #14

TOOL NUMBER  6160

PART CNTR 51635

FLANGE

TWO HAND S.S.
PRESS ANGLE  270

CAMBIE

AL ESPANOL

USE THE CURSOR KEYS

ENABLE SENSORS

TO MAKE SELECTIONS.

COUNTERS

PRESS ENTER TO 

CAM SWITCH

ACCESS SELECTION.

BRAKE MONITOR
TONNAGE/WAVEFORM
PROCESS MONITOR
FEED CONTROL
PM MONITOR
TOOL INFORMATION
SHUTHGT/CNTRBAL
ERROR LOG
LOAD NEW TOOL
DIALOG MENU
TOGGLE HOT KEYS 1

270

F1

F2

F3

F4

F5

F6

F7

F8

Status box

Descriptive labels for

Function keys and Hot keys

Crank Angle/SPM

readout

Crank angle clock

Instructions

Menu

Run window

Figure 3 - 15.  SmartPAC 2 Display, Run Mode

The SmartPAC 2 display shows at the top a status box that contains information such as the
press name and the press speed or angle.  Below that is an area, the Run window, that
contains menu items, instructions, graphics and other components.  Next to the function keys
are eight rectangles that contain descriptions of the function key operations, if any function
keys are currently active.  In Run mode, if you have programmed Hot keys (see page 185),
their labels show up on the main Run menu screen, with red borders.

In every mode, you progress from menu to menu by use of the ENTER and RESET keys, as
instructed on the display.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов