manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 173 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 173

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 151

Foot Switch Test (with Optional Foot Switch)

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

MISSING SAFEGUARDS

Install a light curtain for use with the foot switch option.  A light curtain is required for using
the foot switch.

Failure to comply with these instructions will result in death or serious injury.

WARNING

!

ELECTRIC SHOCK HAZARD WHEN WORKING INSIDE ENCLOSURE WITH POWER ON

•

DO NOT touch electrical connections or circuit boards.

•

Ensure that this test is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

Perform this test only if your SmartPAC 2 with WPC is equipped with a Foot Switch.  If
necessary, refer to the LED map, Figure B at the end of the manual, when you are directed to
the WPC control board.

NOTICE

These instructions refer to the Auto Carry-up angle, which is factory set to

      

•

  170

°

 if it does 

not

 have a light curtain.

      

•

  149

°

 if the press does have light curtain

Refer to instructions for using Auto Carry-up, page 235 for detailed information about the
Auto Carry-up feature.

1.

 

Set the STROKE SELECT switch to OFF and set the MODE to FOOT.  Now, set the
STROKE SELECT switch to SINGLE STROKE

2. Set Press Option switch 3 OPEN. Remember to power down, then power back up to

enable the change. The WPC is now in the FOOT TRIP mode.  After it is tripped, the
press should run to top stop.  On the WPC control board, the “Continuous selector” LED
should be off, the “Single Stroke select” LED should be on, and the “Foot selector” LED
should be on.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов