manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 161 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 161

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 139

Anti-repeat Test

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

OPERATOR STATION MAY NOT MEET SAFETY REQUIREMENTS

Ensure that the operator station is wired correctly.

Ensure that on any non-Wintriss operator station run buttons are placed so that two hands
are required to push both buttons at the same time and no one can press both buttons with
one hand or with one hand and one elbow or in any other way.

Ensure that on any non-Wintriss operator station the run buttons have guard rings or other
means in place to prevent unintentional operation.

Failure to comply with these instructions will result in death or serious injury.

Perform the following test to verify that the press will cycle only once in Single Stroke when
you press both run buttons simultaneously.

1. Set the STROKE SELECT switch to SINGLE STROKE.

2. Press and hold down both run buttons while the press cycles and continue to hold them

down for ten seconds after the press stops.  The press should make only one stroke
(cycle) and then top stop. It should not make any more strokes while you hold down the
run buttons.

•

If the press makes one stroke (cycle) and then stops, it is operating correctly. Go to
the next applicable test.

•

If the press 

does

 cycle again after making one stroke, check the wiring. Repeat the

test in step 2.  If the press still cycles again after it makes one stroke, 

stop!  

 

Turn off

the press.  Contact Wintriss Tech Support.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов