Honeywell SmartPAC 2 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 160

1126800

SmartPAC 2 with WPC Integration

Page 138

Chapter 2

Installing SmartPAC 2 and WPC

Anti-tiedown Test

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

OPERATOR STATION MAY NOT MEET SAFETY REQUIREMENTS

Ensure that the operator station is wired correctly.

Ensure that on any non-Wintriss operator station run buttons are placed so that two hands
are required to push both buttons at the same time and no one can press both buttons with
one hand or with one hand and one elbow or in any other way.

Ensure that on any non-Wintriss operator station the run buttons have guard rings or other
means in place to prevent unintentional operation.

Failure to comply with these instructions will result in death or serious injury.

Perform the following test to verify that the operator station is correctly installed and wired
to require two hands to press both run buttons simultaneously.

1. Set the STROKE SELECT switch to SINGLE STROKE.

2. Press and hold down both run buttons. The press cycles to makes one stroke.

3. While still holding down the left button, do the following: Remove your right hand from

the right button for a moment. Then press the right button again. The press should

not

cycle again.

•

If the press

does not

cycle, go to the next step to perform the test for the other side.

•

If the press

does

cycle, check the wiring. Repeat the test starting with step 2. If the

press still cycles, contact Wintriss Tech Support.

4. Remove hands from the buttons. Then press and hold down both run buttons. The press

makes a stroke.

5. While still holding down the right button, do the following: Remove your left hand from

the left button for a moment. Then press the left button again. The press should

not

cycle

again.

•

If the press

does not

cycle, your anti-tiedown test is complete. Go to the next test.

•

If the press

does

cycle, check the wiring. Repeat the test starting with step 4. If the

press still cycles,

stop!

Turn off the press. Contact Wintriss Tech Support.

«
...
158
159
160
161
162
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов