Honeywell SmartPAC 2 Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 154

1126800

SmartPAC 2 with WPC Integration

Page 132

Chapter 2

Installing SmartPAC 2 and WPC

Check Dual Safety Valve (DSV) Wiring

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

Failure to comply with these instructions will result in death or serious injury.

WARNING

!

ELECTRIC SHOCK HAZARD WHEN WORKING INSIDE THE ENCLOSURE

Turn off and disconnect power from WPC clutch/brake control, the press and any other
machinery it is connected to before working inside the enclosure. This includes power to the
press’s motor.

Failure to comply with these instructions could result in death or serious injury.

Follow the checkout procedure below to ensure that the dual safety valve is wired correctly.
Proper installation and operation of the DSV is vital to personnel safety.

1. Power down the press and the press control.

2. On the WPC Power Supply board, remove one of the DSV fuses. (See Figure 2 - 36, page

3. Power up the press and SmartPAC 2 with WPC. Select INCH with the Stroke Select

switch. Push both RUN/INCH buttons. Observe what happens.

•

If the ram does not move and the display show F79 or one of the DSV valve faults,
this is correct. Go on to the next step.

•

If the ram moves and/or the display shows a different fault, check the wiring of the
DSV valve. Repeat this step. If the ram still moves and/or the display still shows a
different fault, immediately power down the press and contact Wintriss Tech Support.

4. Power down the press and the press control.

5. On the WPC Power Supply board, replace the fuse you removed in step 2 and remove the

other DSV fuse.

6. Power up the press and press control. Push both RUN/INCH buttons. Observe what

happens.

•

If the ram does not move and the display show F79 or one of the DSV valve faults,
this is correct. Go on to the next step.

•

If the ram moves and/or the display shows a different fault, check the wiring of the
DSV valve. Repeat this step. If the ram still moves and/or the display still shows a
different fault, immediately power down the press and contact Wintriss Tech Support.

«
...
152
153
154
155
156
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов