Honeywell SiX Series Скачать руководство пользователя страница 1

 

SiXCO 

Wireless Carbon Monoxide (CO) Detector/ Wireless Carbon Monoxide (CO) Detector 

Installation Instructions 

Instructions d’installation 

This device is intended for use with Honeywell control 
panels that support SiX series devices. Before installing 
detectors, please thoroughly read these installation 
instructions. 

This device is intended for use with Honeywell 
control panels that support SiX series devices. 
Before installing detectors, please thoroughly read 
these installation instructions. 

Features 

Features 

  10-year life 

  CO Detector End-of-Life reporting (detector needs 

replacing) 

  Carbon Monoxide detector maintenance reporting  

  Low Battery Detection 

 

Multi-color status LED 

  10-year life 

  CO Detector End-of-Life reporting 

  Carbon Monoxide detector maintenance reporting  

  Low Battery Detection 

 

Multi-color status LED 

POWER UP 

 

  Remove battery pull tab. Be sure 

batteries are seated properly to 

avoid a low battery condition 

after 15 seconds. 

 

  Upon power up, Green LED 

Blinks every 2 secs / Sounder is 

Silent.  

 

POWER UP 

 

  Remove battery pull tab. Be 

sure batteries are seated 

properly to avoid a low 

battery condition after 15 

seconds. 

 

  Upon power up, Green LED 

Blinks every 2 secs / 

Sounder is Silent.

 

ENROLLMENT  

ENRÔLEMENT 

This device can be enrolled and programmed either 

before or after installation. 

1.

 

Set the Lyric Controller in Programming Mode and go to 

Zone Programming.  Select Add New and then Serial 

Number.  

2.

 

Remove the battery tabs to activate the device and begin 

the enrollment process. 

3.

 

The Green LED flashes rapidly during enrollment (up to 

about 20 seconds

). 

*NOTE: Enrollment time varies depending on the signal 

strength between the device and the controller. 

 

  The detector sends its unique MAC ID (Serial Number) 

and Services information to the controller.   

 

  The controller registers the device and displays the 

transmitter data on screen. 

4.

 

Enrollment is confirmed when the Green LED is ON for 3 

seconds and the detector chirps. 

5.

 

Press SAVE. 

 
 
 

Le dispositif peut être enrôlé et programmé avant 

ou après l'installation.

 

1.

 

Réglez le 

contrôleur Lyric

 en mode de 

programmation et accédez à la programmation 

des zones. Sélectionnez Add New (ajouter 

nouveau) et ensuite Serial Number (numéro de 

série).  

2.

 

Retirez la languette qui recouvre la pile pour 

activer le dispositif et commencer la procédure 

d'enrôlement. 

3.

 

La DEL verte clignote durant l'enrôlement 

(pendant jusqu'à environ 20 secondes*). 

NOTE

:   La durée de l'enrôlement varie selon la 

 

puissance du signal entre le dispositif et 

 

le contrôleur. 

 

Le dispositif transmet au contrôleur son ID 

MAC (numéro de série) et l'information pour les 

services.   

 

Le contrôleur enregistre le dispositif et affiche 

les données du transmetteur sur l'écran. 

 
 

Содержание SiX Series













Отзывы: