manualshive.com logo in svg

Honeywell S9240F1004, Руководство по установке, Страница: 27 / 28

Поделиться
Скачать
Honeywell S9240F1004 Скачать руководство пользователя страница 27

S9240F1004 MODULATING HOT SURFACE IGNITION INTEGRATED FURNACE CONTROL

27

69-2088—01

Compressor Heating/Cooling Display – System Status

LED Error Codes

There are four types of LED error codes:
• Warning Only: IFC continues normal operation.
• Wait for Recovery: IFC resumes normal operation after 

fault recovers.

• Soft Lockout: A state caused by failure internal to the 

control or by a system fault such as loss of flame or 

pressure switch failure. Heating related functionality is 

inhibited during Soft Lockout. Assuming the fault that sent 

the IFC to Soft Lockout has cleared, Soft Lockout exits 

after the Auto Restart Delay when a call for heat is active. 

The operator can cycle power to remove the Soft Lockout 

without waiting for the Auto restart Delay.

• Hard Lockout: A state caused by a failure internal to the 

control or by a system fault such as a flame rollout. Heating 

related functionality is inhibited during Hard Lockout. Hard 

Lockout can be exited only by cycling power to the IFC.

Table 11. Compressor Heating/Cooling LED Display.

Description

Display Example

a

 

(LED display in bold)

a

The current display mode is immediately interrupted if the operating mode changes

Heating Stage: 

Shows what stage of furnace heating is currently operating. Shown only while heating is 

active and unit is set up to work as staged equipment (not modulating).

The display example in this table shows the LED display when the 1st stage heat is active.

H 1

Pause

Display CFM

Repeat

Dehumidification Mode:

Shows that the unit is providing dehumidification instead of straight cooling.

D

Pause

Display CFM

Repeat

Cooling Stage:

Shows what stage of cooling is currently operating.

The display example in this table shows the LED display when the 2nd stage cooling is 

active.

C 2

Pause

Display CFM

Repeat

Defrost Mode:

Shown only while in an active defrost

(simultaneous Y, W, and O).

D F

Pause

Display CFM

Repeat

Table 12. LED Status Codes.

Error/Fault Condition

Code

Error Handling 

(in addition to displaying error code)

Result

Outside air sensor out of range

(open or no discharge air sensor is OK)

180 None

Warning 

Only

Low flame in run mode

240 None

Discharge air sensor (DAS) out of range 

(open or no discharge air sensor is OK)

310 None

Firing rate reduced to match CFM

311 Reduce firing rate every 60 seconds to match available CFM.

Restricted airflow cooling or continuous fan

312 None

Line voltage low

110 Resume normal operation after fault recovers.

Wait for 

Recovery

Line voltage high

113 Resume normal operation after fault recovers.

Zero crossing not detected or frequency out of 

range 

115 Resume normal operation after fault recovers.

Low 24 volts

115 Resume normal operation after fault recovers.

Flame circuit check error

125

a

Resume normal operation 300 seconds after fault recovers.

Hardware failure

125

a

Resume normal operation 300 seconds after fault recovers.

Micro inter-communication failure

125

a

Resume normal operation 300 seconds after fault recovers.

Circulator communication failed

201 Resume normal operation after fault recovers.

Gas valve miswire

204 Resume normal operation after fault recovers.

Low pressure switch failed (stuck) Open 

223 If longer than 300 seconds, start pressure switch calibration.

Содержание S9240F1004





























Отзывы:

Нет отзывов