manualshive.com logo in svg

Honeywell S89E, Быстрый старт, Страница: 6 / 12

Поделиться
Скачать
Honeywell S89E Скачать руководство пользователя страница 6

S89E,F DIRECT SPARK IGNITION CONTROL MODULE

68-0066—4

6

Fig. 3. S89F typical hookup in direct spark control system. See Fig. 9 for control system ladder diagram.

10.

Turn off gas supply.

11.

Gas control closes.

12.

The module begins the safe start check (S89E: 10 

seconds maximum) or safe start check plus valve on 

delay (38 seconds maximum) after which the igniter 

starts and gas control opens.

13.

Time system until gas control closes. S89 is now in 

safety lockout. The lockout time should be within the 

specifications in Table 2. 

14.

Open gas supply. System remains off and no gas flows 

to the main burner.

Table 2. S89 Lockout Times.

Resetting S89 After Safety Lockout

Once the S89 locks out, it must be reset before the system will 

operate. To reset, set the thermostat below room temperature, 

wait at least 45 seconds, then turn the thermostat up to call for 

heat. The system should start normally. If adjusting the 

thermostat does not reset the S89, turn off power to the 

appliance for 45 seconds and then turn it on.

Final Checkout

With power and gas supply on, set thermostat to call for heat 

and observe operation through at least one complete cycle to 

make certain that all controls are operating safely.

OPERATION

The S89 is powered by a 24V transformer. It operates in 

response to a call for heat from the thermostat.

BLUE

WHITE

GROUND

BURNER

IGNITER

M19837

FLAME

SENSOR

120 V SPARK
GENERATOR

BLACK

AIR
PROVING
SWITCH

DUAL VALVE
COMBINATION
GAS CONTROL

COMBINATION
AIR BLOWER
RELAY

THERMOSTAT OR
CONTROLLER

COMBUSTION AIR
BLOWER MOTOR

GND (BURNER)

24V (GND)

24V

VALVE

S89F GAS PRIMARY

TRANSFORMER

L2

L1
(HOT)

L2

L1
(HOT)

LIMIT
CONTROLLER

VALVE (GND)

SENSE

BLUE

1

4

2

3

3

2

1

4

POWER SUPPLY.  PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

ALTERNATED LIMIT CONTROLLER LOCATION.

IMPORTANT:

   •  CONNECT 

L1

 TO THE 

BLACK

 LEAD.

   •  CONNECT 

L2

 TO THE 

WHITE

 LEAD. OTHERWISE THE S89 WILL NOT DETECT THE FLAME AND WILL LOCK OUT.

FACTORY TEST TERMINAL. DO NOT USE.

Lockout Time 

Shown on S89 

Module

Safety Lockout Time

Minimum

Maximum

4 seconds

3.0 seconds

5.5 seconds

11 seconds

8.0 seconds

15.0 seconds

Содержание S89E













Отзывы:

Нет отзывов