manualshive.com logo in svg

Honeywell S89E, Быстрый старт, Страница: 3 / 12

Поделиться
Скачать
Honeywell S89E Скачать руководство пользователя страница 3

S89E,F DIRECT SPARK IGNITION CONTROL MODULE

3

68-0066—4

Approvals:

Underwriters Laboratories Inc. Component Recognized: File 

No. MP268, Guide No. MCCZ2.

CSA International Certified: 158158-1047805.

Fig. 1. S89 dimensions in in. (mm).

INSTALLATION

When Installing This Product…

1.

Read these instructions carefully. Failure to follow them 

could damage the product or cause a hazardous 

condition.

2.

Check the ratings given in the instructions and on the 

product to make sure the product is suitable for your 

application.

3.

Installer must be a trained, experienced service 

technician.

4.

After installation is complete, check out product 

operation as provided in these instructions.

WARNING

Fire or Explosion Hazard.

Can cause severe injury, death or property 

damage.

1. Disconnect power supply before wiring to avoid 

electrical shock, explosion, or equipment damage.

2. If a new gas control is being installed, turn off gas 

supply before starting installation. Conduct Gas 

Leak Test after gas control is installed.

3. In an LP gas installation, remember that LP gas is 

heavier than air and will not vent upward naturally. 

Do not operate electric switches, lights, or 

appliances until you are sure that work area is free 

of gas.

4. Never install an S89 where water can flood, drip, or 

condense on the device. It can malfunction if it gets 

wet.

5. Never try to use a device that has been damp or 

wet—replace it.

6. If the control might be exposed to water or moisture, 

install it in a suitable waterproof enclosure.

7. Any replacement S89 must have the same or 

shorter lockout time 

and

 the same or longer delay 

timing as the original control.

Replacement Application Requirements

If this is a replacement application, follow the appliance 

manufacturer instructions, if available. The manufacturer 

usually provides wiring diagrams, start-up and checkout 

7/8 (22)

3-3/8 (86)

3-3/8 (86)

4-1/16 (103)

7/8 (22)

4-1/16

(103)

2 (51)

M2331

12 (305) LEADS

5-13/16

(132)

2 (51)

7/8

(22)

2-7/8 (73)

1/4 IN. Q.C.

3/8 (86)

HOLE (4)

1/4 IN. Q.C. (1)

3/16 IN. Q.C. (5)

3/8 (10)

Содержание S89E













Отзывы:

Нет отзывов