Honeywell PW7K1R1E Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

Honeywell PW7K1R1E Скачать руководство пользователя страница 7

Introduction

Liability

PW7K1R1E Configuration and Installation Guide,

Document 800-26498

7

Returned units are repaired or replaced from a stock of reconditioned units. Returns
must be accompanied by a Returned Merchandise Authorization (RMA) number
obtained from customer service, and prepaid postage and insurance.

1.3 Liability

You should use the Interface only to control exits from areas where an alternative
method for exit is available.

This product is not intended for, nor is rated for operation in life-critical control
applications.

Honeywell Security Access is not liable under any circumstances for loss or damage
caused by or partially caused by the misapplication or malfunction of the product.

Honeywell Security Access's liability does not extend beyond the purchase price of
the product.

1.4 FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

«
...
5
6
7
8
9
...
»

Содержание PW7K1R1E





























Отзывы:

Нет отзывов