manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 10 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 10

10

SCS Series Manual —

 P/N 15712:L  7/18/16

About This Manual

UL 864 Compliance

1.2  UL 864 Compliance

1.2.1  Products Subject to AHJ Approval

This product has been certified to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, 
UL 864 9th Edition. Operation of this product with products not tested for UL 864 9th Edition has not been evaluated. Such operation 
requires the approval of the local Authority Having Jurisdiction (AHJ).

Products mentioned in this manual that have not received UL 864 9th Edition certification:

•

AM2020/AFP1010

•

NFS-640

•

NFS-3030

•

NCA

•

INA

•

XP Transponders

•

XP5 Transponders

•

CMX/MMX control and monitor modules

•

MPS-24A

1.2.2  Application Not Consistent with UL and NFPA Standards

The HVAC mode is not consistent with the UL and NFPA standards for smoke control. This mode should be used for fan shutdown and 
building heating, ventilating, and air conditioning purposes only. This application is described in Heating, Ventilating & Air Conditioning 
(HVAC) Mode on page 65 and HVAC Wiring Diagrams on page 150.

1.3  Supplemental Documentation

The table below provides a list of documents referenced in this manual, as well as documents for selected other compatible devices. The 
Veri•Fire Tools Programming Utility is available for download from the manufacturer’s website. The document series chart (DOC-NOT) 
provides the current document revision. A copy of this document is included in every shipment.  

Compatible Conventional Devices (Non-addressable)

Document Number

Device Compatibility Document

15378

Fire Alarm Control Panel (FACP) and Network Annunciator

Document Number

NFS-320 Listing Document 

52745LD

NFS-640 Installation, Operations, and Programming Manuals

51332, 51334, 51333

NFS2-640 Listing Document 

52741LD

NFS-3030 Installation, Operations, and Programming Manuals

51330, 51344, 51345

NFS2-3030 Listing Document

LS10006-051NF-E

AM2020/AFP-1010 Manual

15088

NCA Network Control Annunciator

51482

NCA-2 Network Control Annunciator

52482

SLC Wiring Manual

51253

Note: For intelligent SLC devices, refer to the SLC Wiring Manual

Cabinets & Chassis

Document Number

CAB-3/CAB-4 Series Cabinet Installation Document

15330

ABS-4D Backbox Product Installation Document

15073

Other System Components

Document Number

LDM Series Lamp Driver Annunciator 

15885

XP Transponder Manual

15888

XP10-M

I56-1803

XP5 Series Manual

50786

XP6-C 

I56-1805

XP6-MA

I56-1806

XP6-R 

I56-1804

Table 1.1  Reference Documentation

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов