Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 68

Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 34

34

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

System 5000 (UL 8th)

AIM-200 Point Annunciation

System 5000 CPU Annunciator Point Assignments to LDMs

System 5000 Option Modules Annunciator Point Assignments to LDMs

Notes:

1.

Control Switches marked 'not used' will still function as local LAMP TEST or local ACKNOWLEDGE switches for their
respective points.

2.

If Alarm Only Mode is selected, column labeled Yellow LED is not applicable and control switches do not function.

3.

If the 8-Point Shift (DIP switch #4 of SW3) is set ON, the eight System 5000 CPU functions (ACK, SIL, RESET, LAMP TEST,
NAC1, NAC2, MUNTIE, RELAY) will be shifted from annunciator points 1 through 8 (as shown above) to points 57 through 64
(provided those points exist in the system and the LDM-32 is set to address 01).

4.

Optional control switches are active only if all of these conditions are met:
a) '8-Point Shift' (DIP switch #4) is set to OFF.
b) Receive Only (DIP Switch #5) is set to OFF.
c) Switch Inhibit (DIP Switch #7) is set to OFF.

5.

These Status LEDs are active only when the System 5000 is programmed for Output Status.

6.

Use green LEDs to indicate activation on controlled output circuits.

7.

These control switches require that the System 5000 be programmed for Output Control.

B.6 AIM-200 Point Annunciation

The CPU-5000 can be programmed for an alternate method of annunciating the AIM-200. Up to 192 intelligent devices can be annunci-
ated on a single AIM-200 with LDM series annunciators. The System 5000 annunciates the AIM-200 installed directly to the right of the
CPU-5000. Note that an annunciator cannot be used to execute manual ON/OFF control of intelligent AIM-200 points only standard
System 5000 zones. The option provides annunciation of up to 256 points for the System 5000, broken down as follows:

•

Annunciator Address 1:
– 8 CPU points (CPU point shift not an option).
– 8 unusable points (redundant AIM-200 points).
– 48 points mapped to the next six modules installed in the

System 5000

(which can also be AIM-200s for annunciation of their 8

software zones.)

System 5000 CPU

Points

LDM Alarm LED Red

LDM Trouble/Supv Led Yellow

LDM Control Switches

Annunciator Point #1

Indicates System Alarm

Indicates System Trouble

Functions as an

ACKNOWLEDGE

Annunciator Point #2

not used

Indicates that signals have been

silenced

Functions as a SIGNAL

SILENCE

Annunciator Point #3

not used

not used

Functions as a SYSTEM

RESET

Annunciator Point #4

not used

Indicates Supervisory Condition

not used

Annunciator Point #5

Indicates that Notification Circuit 1 has

been activated

4

Indicates trouble status of circuit

Controls Notification Circuit 1

Annunciator Point #6

Indicates that Notification Circuit 2 has

been activated

4

Indicates trouble status of circuit

Control Notification Circuit 2

Annunciator Point #7

Indicates that the Remote Signaling

Municipal Tie has been activated

4

Indicates trouble status of circuit

Controls Remote Signaling

Municipal Tie

Annunciator Point #8

Indicates that the Alarm Relay has

been activated

4

Indicates Module Trouble, Power

Failure, or Disabled Circuit(s)

Controls Alarm Relay

Table B.1 System 5000 CPU Annunciator Point Assignments to LDMs

System 5000

Option Modules

LDM Alarm LED Red

LDM Trouble/Supv Led Yellow

LDM Control Switches

IZM-8

Alarm Status per Circuit

Trouble Status per Circuit

not used

ICM-4, ICE-4

Indicates Activation

3, 4

Indicates Trouble per Circuit

Controls Notification Circuit

5

CRM-4, CRE-4

Indicates Activation

3, 4

Indicates Trouble per Circuit

Controls Relays

5

TCM-2, TCM-4

Indicates Activation

3, 4

Indicates Trouble per Circuit

Remote Switch Functions

5

AIM-200

Indicates Alarm Status of eight

software zones

Indicates Trouble Status of eight

software zones

not used

Table B.2 System 5000 Option Modules Annunciator Point Assignments to LDMs

«
...
32
33
34
35
36
...
»

Содержание NOTIFIER LDM Series





































































Отзывы:

Нет отзывов