background image

 

 

Disclaimer 

Honeywell International Inc. (“HII”) reserves the right to make changes in 

specifications and other information contained in this document without prior 

notice, and the reader should in all cases consult HII to determine whether any 

such changes have been made.  The information in this publication does not 

represent a commitment on the part of HII. 

HII shall not be liable for technical or editorial errors or omissions contained 

herein: nor for incidental or consequential damages resulting from the furnishing, 

performance, or use of this manual. 

This document contains propriety information that is protected by copyright.  All 

rights reserved.  No part of this document may be photocopied, reproduced, or 

translated into another language without the prior written consent of HII. 

© 2008 – 2011 Honeywell International Inc.  All rights reserved. 

Web Address: www.honeywellaidc.com 

Trademarks 

Metrologic, MetroSelect, MetroSet2 and TotalFreedom are trademarks or 

registered trademarks of Metrologic Instruments, Inc. or Honeywell International 

Inc. 

Microsoft, Windows, and Windows 95 are trademarks or registered trademarks of 

Microsoft Corporation. 

Other product names mentioned in this manual may be trademarks or registered 

trademarks of their respective companies and are the property of their respective 

owners. 

 

Содержание MS4980





















































Отзывы: