manualshive.com logo in svg

Honeywell MPA1C1, Руководство по установке

Поделиться
Скачать
Honeywell MPA1C1 Скачать руководство пользователя страница 6

5

MPA1C1 Overview

An MPA1C1 access control unit is a full-featured single-door 

web-based smart edge access control system. 
The MPA1C1 panel includes a built-in web server, built-in Ether

-

net, and PoE (Power over Ethernet) capability. You can manage 

the access control system using either a web browser, MPC 

(MAXPRO® Cloud) or WIN-PAK. 
For supported configurations, see  beginning on page 32 to view 

illustrations of the supported MPA1C1 system configurations.

Note:

• The MPA1C1 web server/browser is intended for monitoring and 

programming use only.

• MPC and WIN-PAK software are intended for monitoring and 

programming use only, and have not been evaluated by UL.

Panel Components and Descriptions

Note:

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not 
cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation.

The MPA1C1 panel consists of a web browser enabled control

-

ler, and a PoE power supply. The following figures show the 

MPA1C1 panel wiring and components and the typical door 

configurations that the panel can be used in.

Содержание MPA1C1





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды