background image

 

 

 AND ADJUSTMENT PROCEDURES FOR HONEYWELL 

 

OR MP-953F PNEUMATIC OPERATORS USED ON ARMSTRONG HUMIDIFIERS

12.

13.

14.

15.

16.

Place the operator base (26)' onto the frame 

 and

secure it in place with screws (25).
Invert the operator

back to its upright position.

Place the diaphragm (21) and follower (38) into the

frame (29).

Place the washer (32) around the top of the support

 and turn on the nut (34). Tighten securely.

With outer edge of the diaphragm (21) in the groove of
the frame 

place the cove-r (33) over the frame.

Align the screw holes.
Attach the cover with the cover screws (31). Tighten

securely.
Install the -pneumatic operator in accordance with

V.

CHANGIN

THE ROLLING SEAL

To

1.

2.

3.

replace a rolling seal, perform the following steps.

4.

5.

6.

7.

8.

Remove the pneumatic operator in accordance with
Section I.
Perform Section IV (CHANGING OPERATOR SPRINGS) steps 2
through 8 to disassemble the operator.
With the operator in the upright position, remove the
three screws (23) and ring (39) that secure the rolling
seal (22).
Remove the rolling seal (22).

Then separate the cup

(37) from the old seal.

Place the cup (37) into the new rolling seal.

Install

the new seal in the frame.
Secure the new rolling seal (22) in place with the ring

(39) and three screws (23). Tighten securely. Be sure

that the edge of the rolling seal is in the groove in
the frame.

Perform Section IV steps 10 through 15 to reassemble

the operator.

Be sure that the spring (30) is in

place.

Install the pneumatic operator in accordance with

Section II.

VI.

REPLACING THE HUMIDIFIER VALVE AND SEAT

To replace the humidifier valve and seat,

perform the

following steps.

1.

Remove

the pneumatic operator in accordance with

Section I.

2.

Remove the bonnet assembly (15) from the 

cap.

4

Содержание MP953B









Отзывы: