Honeywell MAXPRO NVR Hybrid PE Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 360

Honeywell MAXPRO NVR Hybrid PE Скачать руководство пользователя страница 63

MAXPRO NVR 5.0 Installation and Configuration Guide

63

4

Installing the NVR Software

Overview

This chapter describes the procedures for installing the MAXPRO NVR software. Follow the
appropriate section in this chapter to complete your MAXPRO NVR software installation.

Caution:

For Honeywell’s turnkey box solutions, MAXPRO NVR XE/SE/PE and
MAXPRO NVR Hybrid XE/SE/PE, the server and client software required is
pre-installed on the box. The instructions in this chapter for Server
software fresh installation are

NOT

applicable for the turnkey box

solutions. On the NVR and Hybrid NVR box solutions, only the installation
upgrade process might apply depending on the existing software version
on the unit. For client workstations, the client installation procedure is
applicable.

Before you Begin

The client and server computers must meet the hardware and software specifications listed in
the respective NVR Data Sheet.

M A X P R O N V R S o f t w a r e - O p e r a t i n g S y s t e m P r e r e q u i s i t e s

Before you install Honeywell MAXPRO NVR software, please note the MAXPRO NVR Server
and Client operating system requirements listed in the following section.

•

MAXPRO NVR Server

The computer that is designated as the server must run on one of the following operating
systems:

•

Microsoft® Windows® 7 Professional 32-bit / 64-bit, Service pack 1 or Windows
8.1 Professional 32-bit/64-bit or Windows 10 Professional 32-bit/64-bit must be
installed on the NVR before installing MAXPRO NVR software.

•

Microsoft® Windows® Server 2008 R2 Standard, Service pack 1 or Windows
Server 2012 R2 Standard must be installed on the NVR before installing
MAXPRO NVR Software.

•

MAXPRO NVR Client Workstation

The computer that is designated as the client workstation must run on one of the following
operating systems:

•

Microsoft® Windows® 7 Professional 32-bit / 64-bit, Service pack 1 or Windows
8.1 Professional 32-bit/64-bit or Windows 10 Professional 32-bit/64-bit must be
installed on the workstation before installing MAXPRO NVR client software.

Please refer to the

Microsoft® Windows Patches Tested with MAXPRO®NVR

document for

further details on Windows updates that have been tested with the current software version
shipping with MAXPRO NVRs.

«
...
61
62
63
64
65
...
»

Содержание MAXPRO NVR Hybrid PE









































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды