manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Руководство по установке и настройке оборудования

Поделиться
Скачать
Honeywell MAXPRO NVR Hybrid PE Скачать руководство пользователя страница 276

S E C U R I N G   M A X P R O   N V R

IPsec Policies for Secured Video Data Transmission

276

 MAXPRO NVR 5.0 Installation and Configuration Guide

1 1

IPsec Policies for Secured Video Data 
Transmission

This section describes how to create highly secured network connections using the IPsec 
policies for secure video data transmission. The recommended types of policies are:

•

Unrestricted

•

Blocked

•

Secured

User needs create these 3 types of policies depending upon the network devices. The detail 
explanation is given below.

Unrestricted Network

Unrestricted network is for connecting within your control (inside LAN), so that you need not 
perform any security settings for communication between the network devices. This also 
applies to devices which cannot establish IPsec communication. 

Example where unrestricted network will be required is as follows:

•

Connections between cameras and recorder (MAXPRO NVR)

•

Connections between Ultra key, Joysticks keyboards to Recorders (MAXPRO 
NVR) and Video Management Solutions (MAXPRO VMS)

Ho w   t o   c o n f i gu r e   U n r e s t r i c t e d   c o n n e c t i o n s   r u l e

1.

In Run command box type 

secpol.msc

 and then click 

OK

. The 

Local Security Policy

window is displayed as shown below.

2.

Under 

Security Settings

 pane, right click on 

IP Security Policies on Local Computer

 

and then select 

Create IP Security Policy

 as shown below.

Содержание MAXPRO NVR Hybrid PE









































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды