Honeywell MagicStat CT3300 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

Honeywell MagicStat CT3300 Скачать руководство пользователя страница 1

MagicStat

®

CT3300 Programmable Thermostat

Installation and Programming Instructions

Welcome to the world of comfort and energy savings
with your new Honeywell MagicStat® Programmable
Thermostat. Your new thermostat will automatically
control the temperature in your home, keeping you
comfortable while saving energy.

If you have any questions about using this thermostat,
visit our home expert Web site at
www.honeywell.com/yourhome or call Honeywell
Customer Relations at 1-800-468-1502.

®U.S. Registered Trademark
Copyright © 2001 Honeywell • All Rights Reserved

Weekday/Weekend (5-day/2-day)
Programmable Heat and/or Cool
Low Voltage (20 to 30 Vac)
Thermostat and Mounting Plate
Model CT3300

Table of Contents

Installation

Programming

Operation

Change the clock for Daylight/
Standard Time

Set the Fan and System switches

Replace the batteries

Override the program settings

Frequently asked questions

Limited 1-Year Warranty

69- 0654- 5

1
2
3
...
»

Содержание MagicStat CT3300

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды