Honeywell HTRD400 Скачать руководство пользователя страница 36

Страница: 36 / 176

Rev 1.02

Document 900.0328

05/05

Installation

Connecting the Camera(s) to the HTRD400 Recorder

The HTRD400 Recorder has four RJ45 connectors for connecting up to four HTCD50 Digital
Cameras.

Connect the CAT5 straight data/power cable connector from each camera into a CAMERA
ONLY port on the rear panel of the HTRD400 Recorder (see

Figure 2-9

). It does not matter

which CAMERA ONLY port you choose as the unit powers them all at the same time.

Camera Aiming and Focusing

After the HTCD Digital Camera base is mounted, use the Toolbox application on a PC or
laptop connected to the HTRD400 Recorder to:

•

Configure the connected camera

•

Fine tune FOV adjustments

•

Position, aim, and focus the camera

•

Set the image quality and resolution

•

Confirm the video coverage

Note

This section explains how to position, aim, and focus an HTCD Digital
Camera. To set image quality, resolution, and frames per second see

Configuring the Camera(s)

, page

Aiming the Camera

On a connected PC or laptop, start the Toolbox application.

Add and configure the camera (see

Configuring the Camera(s)

, page

On the camera, loosen the pan thumbnut and tilt screws (x2) to adjust the camera to
the desired view.

HTCD50 camera: See

Figure 2-11

HTCD52 camera: See

Figure 2-12

Confirm the desired field of view and image quality on the Camera Edit screen (see

Configuring the Camera(s)

, page

Содержание HTRD400

















































































































































































Результаты поиска

Содержание HTRD400

Отзывы:

Honeywell HTRD400, Справочное руководство, Страница: 36 / 176

Результаты поиска

Содержание HTRD400

Отзывы: