Honeywell HM750 Скачать руководство пользователя страница 2

Страница: 2 / 28

HM750A1000

33-00289—01

Table 1. Specifications.

Fig. 1. Specification label location.

CAUTION

Servicing

Disconnect main power before any servicing.

• The plumbing and electrical compartments

contain high voltage components and wiring.
Access should be limited to authorized
personnel only.

• During and following operation of the

humidifier, the steam and components in
contact with the steam such as the steam lines,
steam distributors, and condensate lines can
become hot and can burn if touched.

• Honeywell does not accept any liability for

installations of humidity equipment installed by
unqualified personnel or the use of
parts/components/equipment that are not
authorized or approved by Honeywell.

• To maintain warranty, only Honeywell

approved parts and cylinders may be used in

the operation of the product.

CAUTION

Electrical

All electrical work should be done according to

local and national electrical code.

Electrical connection to be performed by a licensed

electrician.

Unit recommended to be powered by a dedicated

GFCI circuit.

CAUTION

Plumbing

Plumbing to be performed by a licensed plumber.
Drain water from humidifier can be very hot. Do not

drain to public sink.

All plumbing work should be done according to

local plumbing code.

CAUTION

Installation

Do not mount on surfaces hotter than 176 ºF

(80 ºC).

Do not mount in area where freezing can occur.
Do not mount on vibrating surface.
Do not mount on floor.
The HM750 produces steam at atmospheric

pressure. No devices which could block steam
output should be connected to the steam outlet.

Steam lines must be installed so that no restriction

can produce backpressure in the humidifier.

Do not mount outdoors without protection against

rain, snow, condensation or equivalent.

CAUTION

Water quality

The Honeywell HM750 requires a cold water

connection from your home's main water supply
between 15-100 PSIG. A throttle valve may be
necessary, and a water shut-off valve is
recommended for safety.

Reverse Osmosis (RO)

and Deionized (DI) water must not be used.

Water conductivity is important to ensure the
electrode humidifier operates effectively.
Honeywell recommends 125-1200

S/cm

(microsiemens/cm).

Volts

Steam Output

GPD

Amps Phase

Max Ext.

Fuse

(Amps)

Standard

Cylinder

Net/Full

Weight

lbs. (kg)

Dimensions

(W x H x D)

110/120

1.5

HM750ACYL

15 / 20

(7.0 / 9.5)

10 x 18 x 7 in.

254 x 457 x 178 mm

220/240

3.0

MODE

HM750

A100

0 1

PHASE:

HZ:

try o

f or

igin

: C

ada

Pay

s d

’orig

ine

: Ca

nad

to-A

dap

tive

Pro

fes

sio

nall

y se

rvic

ed o

nly

tretien

par

des

pro

fess

ionn

els s

eule

men

S/N

DATE

CODE

205X

HUM

IDIFIE

110

-12

220

-24

GPD

1.5

3.0

HM750

Statu

Servic

Power

Idle

Filling

Humid

ifying

Draining

Cylind

Fault

Drain

Fault Code

s In Front Cov

MODEL:

HM750A1000

PHASE:

HZ:

Country of origin: Canada
Pays d’origine : Canada

Auto-Adaptive

Professionally serviced only.
Entretien par des professionnels seulement.

S/N

DATECODE

205X

HUMIDIFIER

VOLT

110-120

220-240

AMP

GPD

1.5

3.0

M37184

MODEL:

HM750A10

00 1

PHASE:

HZ:

Countr

y of ori

gin: C

anada

Pays d’

origine :

Canad

Auto-A

daptiv

Profes

sionall

y servic

ed only

Entretie

n par de

s profes

sionnels s

eulemen

S/N

DATECO

205X

HUMIDIFIER

VOLT

110-12

0 220

-240

AMP

GPD

1.5

3.0

Содержание HM750





























Результаты поиска

Содержание HM750

Отзывы:

Бренды по названию

Популярные бренды

Honeywell HM750, Руководство по установке

Результаты поиска

Содержание HM750

Отзывы:

Бренды по названию

Популярные бренды