Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 34

Страница: 34 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

8.5. Checking the functions before using the instrument

Before installing the HERMetic instrument as described in section 9.10, the following tests are recommended

to ensure that the instrument is ready to work.

8.5.1. Battery

Refer to section 10.2 "

Checking the battery".

8.5.2. Temperature

Switch on the unit.

The buzzer shall beep every 2 sec.

When the temperature is displayed, check that it

shows the surrounding temperature.

8.5.3. Ullage

Switch on the unit.

The buzzer shall beep every 2 sec.

Check the ullage in a glass of water.

Check the ullage by immersing the ultrasonic gap

sensor but not the electrodes (position A); The

buzzer shall beep continuously.

8.5.4. Interface

Switch on the unit.

The buzzer shall beep every 2 sec.

Check the interface in a glass of water.

Check the interface by immersing the interface

electrodes also (position B). The buzzer shall

beep intermittently.

position A

position B

Figure 9-7

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 34 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: