manualshive.com logo in svg

Honeywell HDZ402LIKV, Руководство пользователя, Страница: 24 / 109

Поделиться
Скачать
Honeywell HDZ402LIKV Скачать руководство пользователя страница 24

40X ZOOM IR PTZ DOME CAMERA USER GUIDE 

 

11 

 

Working in the Live Interface 

The toolbar in the upper left corner of the screen, immediately above the video window, 
provides quick access to commonly used controls. 

Figure 12

 Quick Access Toolbar 

 

Table 2 Quick Access Controls 

Icon 

Description 

 Talk

 

Click to enable or disable bidirectional talk (audio must also 
be enabled).  

 Audio 

Click to enable or disable the audio input stream. 

 Manual Track 

Click it and then left click the mouse and drag the mouse in 
the video window to select any zone, you can enable the 
speed dome to track the object in the specified area. 

 Record 

Click to start or stop recording video. The icon appears red 

when video is being recorded, gray when video is not being 
recorded. The recorded video is saved to the location 
specified in 

Setting 

 Storage 

 Destination 

 Path 

 

Live Record

. 

 Triple Snapshot 

Click to take three snapshots in quick succession (1 per 
second). The snapshots are saved to the location specified 
in 

Setting 

 Storage 

 Destination 

 Path 

 Live 

Snapshot.

 

 Snapshot 

Click to take a snapshot of the current video. The snapshot 
is saved to the location specified in 

Setting 

 Storage 

 

Destination 

 Path 

 Snapshot

. 

 Digital Zoom 

When this function is enabled, you can drag over an area of 
the video to enlarge that area. Right-click to return to the 
previous magnification. 

 Alarm Output 

Click to generate or cancel an alarm output. The icon 
appears red when the alarm is active, gray when the alarm is 
inactive. 

 Regional Focus 

Click to enable regional focus. Select an area of the video to 
focus in on by dragging over the area with your mouse. The 
area will come into sharper focus automatically. 

 

Mark 

Add information on the Live interface, and also manage 
added comments 

 Wiper 

Click this button to select wiper operation: Start/Stop/Once. 
Note: Only HDZ402LIWV/HDZ404LIWV/HDZ408LIWV 
model support Wiper. 

 

Содержание HDZ402LIKV














































































































Отзывы:

Нет отзывов