manualshive.com logo in svg

Honeywell ESSER IQ8Control M, Инструкция по установке, Страница: 22 / 138

Поделиться
Скачать
Honeywell ESSER IQ8Control M Скачать руководство пользователя страница 22

Fire Alarm Control Panel IQ8Control C / M 

 

22

  

FB 798951.10.GB0 / 04.15

 

5.1  Maintenance / Service 

Maintenance is necessary for the proper operation of the fire alarm control panel as the function of the system 
parts can be affected by environmental conditions and ageing. Maintenance is regulated by national standards 
(e.g. DIN VDE 0833 in Germany) and guidelines. In addition to the safety directives and notes in this 
documentation, these standards and guidelines, as well as local requirements for the operational location of the 
fire alarm control panel must be observed. 

 
 

 

Depending on the software and system-specific customer data programming of your panel, its 
functions and display representations might differ from the ones described in this manual!  
 
The terminal connections and connections shown in this installation manual relate only to the 
characteristics of the panel operating system software specific to the Federal Republic of  
Germany [D]. 

 
 
 

 

Danger – Electrical shock ! 

Remove all power from the FACP before carrying out any installation work! 
 

ESD protection 

While handling electronic assemblies, the necessary precautions against electrostatic discharge must 
be taken. 
 

Protective and functional earth 

The PE conductor must be connected to the corresponding terminal at the mains supply. Connect the 
FE terminal of the panel’s cabinet with the protective earthing rail (PE rail) of the power distributor 
panel from which the fire alarm system will be powered. 

Commissioning 

A complete system check must be carried out after commissioning and for each modification of the 
customer data programming! 

 

 

 

Содержание ESSER IQ8Control M











































































































































Отзывы:

Нет отзывов