manualshive.com logo in svg

Honeywell ECS Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Honeywell ECS Series Скачать руководство пользователя страница 33

ECS Series Emergency Communication System Installation Manual                                                           151455

4-8

Figure 4-13  ECS-NVCM with ECS-EMG Location for IFP-2100ECS

4.3.2

Installing and Connecting the ECS-EMG to the ECS-SW24

The ECS-SW24 adds 24 switches to the IFP-300ECS and IFP-2100ECS controls for a total of 40. 
(with the 16 Non-ECS switches on the ECS-EMG).

Follow these steps to install and connect the ECS-SW24:

1.

Open Cabinet door and dead front panel.

2.

Remove AC power from the main control panel.

3.

Disconnect the backup batteries.

4.

Install the ECS-SW24 on the six mounting studs located on the inside of the dead front panel. See 
Figure 4-15 for IFP-300ECS or Figure 4-17 for IFP-2100ECS.

5.

For the IFP-300ECS, connect one end of the wiring harness (P/N 130398 supplied) to the ECS-
EMG and the other end to the ECS-SW24 as shown in Figure 4-15.

6.

For IFP-2100ECS connect one end of the wiring harness (PN 130398 supplied) to the ECS-EMG 
and the other end to the P4 connector on the NVCM as shown in Figure 4-16. If two ECS-SW24's 
are used, connect one ECS-SW24 to the other ECS-SW24 as shown in Figure 4-17.

7.

Secure the switch expander(s) to the dead front panel using the supplied six ¼” Hex nuts.

8.

Restore AC power.

ECS-NVCM

ECS-EMG

Содержание ECS Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды