Honeywell Dolphin Power Tools Скачать руководство пользователя страница 8

Страница: 8 / 176

1 - 2

Software Requirements

Dolphin Terminals

Power Tools are designed to work with the following mobile device platforms:

• Microsoft

Windows Mobile

2003 Software for Pocket PCs

• Microsoft

Windows Mobile

2003 Second Edition Software for Pocket PCs

• Microsoft

Windows Mobile

5.0

• Microsoft

Windows

CE 5.0 (Dolphin 7600, 6100, 6500)

Desktop

The Power Tools installer and the workstation version of EZConfig Editor are designed to work with the
following operating systems:

• Microsoft

Windows

• Microsoft

Windows

2000

• Microsoft

Windows

• Microsoft

.NET Framework 2.0

• Microsoft

ActiveSync

(version 4.2 or higher)

Dolphin Power Tools Main Window

Note: Check the

Dolphin Power Tools Overview

(see page 1-1) to determine the applicable tools for your device.

ScanWedge

•

SetRAM

•

Suspend

•

SysInfo

•

On Windows Mobile-based Dolphins,
tap

Start

Power Tools

On the Dolphin 7600, 6100, 6500
tap

Start

Programs

Power

Tools

Power Tool

Windows Mobile
5/6

Windows Mobile
2003 Second
Edition

Windows CE
5.0

Содержание Dolphin Power Tools

















































































































































































Результаты поиска

Содержание Dolphin Power Tools

Отзывы:

Бренды по названию

Популярные бренды

Honeywell Dolphin Power Tools, Руководство пользователя

Результаты поиска

Содержание Dolphin Power Tools

Отзывы:

Бренды по названию

Популярные бренды