manualshive.com logo in svg

Honeywell Dolphin Power Tools, Руководство пользователя

Поделиться
Скачать
Honeywell Dolphin Power Tools Скачать руководство пользователя страница 51

3 - 1

3

DeviceConfig

Overview

DeviceConfig consists of the DeviceConfig.exe and the DeviceConfig.exm file located in the 

\IPSM

 

(

\Honeywell

 

for 6100/6500) 

folder. DeviceConfig.exe looks for and applies the settings in the 

DeviceConfig.exm file.

Note: On the Dolphin 7600, the DeviceConfig.exe is located in the \Program Files\Power Tools folder.

DeviceConfig.exm File

The DeviceConfig.exm file contains terminal configuration settings. Because this file is stored in the 

\IPSM

 

(

\Honeywell

 

for 6100/6500) 

folder, its configuration settings persist through cold boots and should 

be considered system defaults. 

Enabling DeviceConfig Functionality

By default, all sections except the 

About Section

 (see page 3-12) are disabled, which means that the key 

values are not applied to the terminal. To use the DeviceConfig.exm file to configure the terminal, enable 
the sections and keys required by your configuration in 

EZConfig Editor

 (page 2-2) on the workstation or 

EZConfig Editor on the Terminal

 (page 2-27). 

Autorun 

Autorun

 (see page 4-1) launches DeviceConfig.exe, which applies the DeviceConfig.exm settings, then 

launches a cold boot followed by a warm boot. 

Bar Code Delivery

When the DeviceConfig.exm file is delivered to the terminal via bar code, EZConfig Client launches 
DeviceConfig.exe automatically after decoding. DeviceConfig.exe then applies the settings in 
theDeviceConfig.exm file in the terminal. For more information, see 

Creating Bar Codes

 (page 2-19) and 

EZConfig Client

 (page 2-31).

The DeviceConfig.exm file 

must

 be associated with DeviceConfig.exe for EZConfig Client to launch 

DeviceConfig.exe after decoding the bar code. In EZConfig Editor, the associated application path must 
be

\IPSM\deviceconfig.exe 

(

\Honeywell

 

for 6100/6500)

For more information, see 

Associating Applications

, page 2-15. 

Settings in Control Panel Applets

Many settings in the DeviceConfig.exm file have matching Control Panel applets on the terminal that allow 
the user to enter and save the same values. If a user changes a setting in the Control Panel applet on the 
terminal, that setting is applied but stored in RAM memory and erased during the next cold boot. During 
the next cold boot, Autorun launches DeviceConfig, which then re-applies the settings in the 
DeviceConfig.exm file.

WLAN Settings

When enabled, the WiFi section of the DeviceConfig.exm file creates profiles that will 
appear in the WLAN control panel applets. Those profiles will have the same names as the 
value entered in the 

SSID

 (see page 3-4) key.

Содержание Dolphin Power Tools

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды