background image

 

56 

Product Service and Repair 

 

Honeywell International Inc. provides service for all its products through service 
centers throughout the world.  To obtain warranty or non-warranty service, 
contact the appropriate location below to obtain a Return Material Authorization 
number (RMA #) before returning the product. 

North America 

Telephone:  (800) 782-4263 

E-mail:  [email protected] 

Latin America 

Telephone:  (803) 835-8000  
Telephone:  (800) 782-4263  
Fax:  (239) 263-9689 

E-mail: [email protected] 

Brazil 

Telephone:  +55 (11) 5185-8222 
Fax:  +55 (11) 5185-8225 

E-mail:  [email protected] 

Mexico 

Telephone:  01-800-HONEYWELL (01-800-466-3993) 
Fax:  +52 (55) 5531-3672 

E-mail:  [email protected] 

Europe, Middle East, and Africa 

Telephone: +31 (0) 40 2901 633 
Fax:  +31 (0) 40 2901 631 

E-mail:  [email protected] 

Hong Kong 

Telephone:  +852-29536436 
Fax:  +852-2511-3557 

E-mail:  [email protected] 

Singapore 

Telephone:  +65-6842-7155 
Fax:  +65-6842-7166 

E-mail:  [email protected] 

China 

Telephone:  +86 800 828 2803 
Fax:  +86-512-6762-2560 

E-mail:  [email protected] 

Japan 

Telephone:  +81-3-6730-7344 
Fax:  +81-3-6730-7222 

E-mail:  [email protected] 

Online Product Service and Repair Assistance 

You can also access product service and repair assistance online at 

Содержание Dolphin 7600

































































Отзывы: