background image

DACT-E3 Product Installation Document —

 P/N 9000-0581:J6  12/16/2019

3

2.3 DACT-E3 Installation

1. Remove the DACT-E3 sub-assembly from its static-shield bag, observing proper static protection measures
2. Visually inspect the unit for damage.

If any components are damaged, notify the shipping carrier immediately. Report missing components to the Gamewell-FCI 
Customer Service.

3. Use the Hardware Kit provided with the unit.
4. The DACT-E3 sub-assembly can be installed in several types of configurations in the E3 Series and SLP-BB cabinets.

For additional information on the DACT-E3 installation, refer to the following documents:

– E3 Series Fire System (Expandable Emergency Evacuation System) UL Listing Document, P/N:LS10080-051GF-E

– S3 Series System (Small Addressable Fire Alarm Control Panel) UL Listing Document, P/N: LS10005-051GF-E

– E3 Series Cabinets B, C, D, Retrofits, DR-C4/DR-D4, and EQ Cabinets Installation Instructions, P/N:LS10082-000GF-E

– E3 Series Remote Annunciator Display Cabinets, P/N:LS10083-000GF-E

2.3.1 DACT-E3 Installation Assembly Options

Table 2.3.1.1 lists the systems, cabinets, and mounting plates that use the DACT-E3.

E3 Series

®

 is a registered trademark of Honeywell International Inc. Ademco

®

 is a registered trademark of Ademco Inc.

©2020 Copyright by Honeywell International, Inc. All rights reserved.

E3 Series Fire

S3 Series             

Retrofit

Cabinet A1 Backbox

SLP-BB Cabinet, B Backbox (P/N:SLP-BB)

IF600 Retrofit B-Slim Cabinet

Cabinet B Backbox

S3 Series, B-Size Cabinet (P/N: E3BB-BB/RB)    

600 XL Retrofit Cabinet C Backbox   

B-Slim Cabinet Inner Door

E3 Series, Cabinet A2 (P/N: E3BB-BA2/RA2)

7200 Cabinet B E3-ILI-C Plate

Cabinet C,E3-INX-C Plate

E3BB-FLUSH-LCD Cabinet A2 (P/N: E3BB-FLUSH-LCD)    7200 Cabinet C E3-INCC-D Plate

Cabinet C, E3-INCC-C Plate     
Cabinet C, E3-ILI-C Plate
Cabinet D, E3-INX-D Plate
Cabinet D, E3-INCC-D Plate    
Cabinet D, Command Center 
Cabinet D, Voice Evacuation

Note: 

For information on the DACT-E3 installation in the E3 Series, Fire, SLP or Retrofit Kits system cabinets and plates, refer to 

the 

S3 Series (Small Addressable FACP) System UL Listing Document, P/N: LS10005-051GF-E.

Table 2.3.1.1  DACT-E3 Cabinet and Mounting Plate Configurations

Содержание DACT-E3















Отзывы: