Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 66

Страница: 66 / 230

Step Procedure

For more
information, see

Install (or verify correct installation of):

External disconnect switches

Fuses at the power source associated with input
sensor or output devices for I/O modules

Installing I/O
modules

section

Arrange and organize items to be installed at or near
enclosures.

Mount racks

ATTENTION: Never mount racks vertically, or with the backplane
horizontal, or upside down.

Figure 5-9: Incorrect rack mounting direction

CAUTION: Mark hole locations then either remove or cover any
equipment below to ensure metal chips generated from drilling /
tapping do not migrate causing electrical hazard or damage.

1. Mount the Rack in the enclosure by completing these steps:

a. Using the diagrams below as a guide, mark the locations for the

top holes in the rack.

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 66 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: