Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 41

41

Component
Type

Comments

connects to UOC. All device IP addresses must be statically assigned.
For further information, see

EtherNet IP User's Guide_EPDOC-X399-

en-510A.pdf

.

Allen Bradley
OPC Server
from
MatrikonOPC

The Rockwell Allen Bradley OPC Server from MatrikonOPC can be
installed on the Experion Server in systems which incorporate UOC.
The Matrikon OPC Server enables one of two methods whereby
ControlLogix tag names can be used to make UDT references in a
UOC strategy. For further information, see

EtherNet IP User's Guide_

EPDOC-X399-en-510A.pdf

.

Studio 5000
Logix
Designer
Software

Studio 5000 Logix Designer Software from Rockwell Allen Bradley is
used in conjunction with UOC configurations to configure IP
addresses of Rockwell Allen Bradley EtherNet/IP devices. It can also
be used to export a file which defines ControlLogix tag names so that
they can be used in Control Builder to construct UDT data references
from UOC. For further information, see

EtherNet IP User's Guide_

EPDOC-X399-en-510A.pdf

.

While using DLR (Device Level Ring) on Stratix 5700 Switch, DO NOT
CONNECT a DLR network to a Non-DLR port on the Switch. DLR
should be connected only to the DLR ports on the switch. Doing this
will result in the entire down link network going down. The recovery is
to only remove the DLR connection from the switch.

Non-Redundant Star to 900 I/O and EIP Devices

In addition to the DLR ring topology, the UOC can also connect to a
non-redundant star EtherNet/IP network through its ETH3 downlink
port. This allows it to communicate simultaneously with ControlEdge
900 I/O as well as EtherNet/IP-capable I/O, devices and PLCs.

Installation and maintenance of a downlink EtherNet/IP network
must be done in accordance with the best practices of Ethernet
networking in general and EtherNet/IP in particular.

In this topology, CPMs connect through their ETH3 downlink port
with ETH4 port disconnected. EPMs connect through their ETH1 port
with ETH2 port disconnected. An example is shown in the diagram
below.

«
...
39
40
41
42
43
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов