Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 174

LED Failure Definition

Number
of
strobes

Failure

Description

User Action

Applies
to

1

Failsafe

The module is in
the failsafe state
because it is not
receiving
message
requests from
the CPU or the
whole system is
in exception
stop.

1. If expansion I/O rack, go to step

2. If non expansion I/O rack, go
to step 3.

2. Check the Scanner status LED If

it’s flashing 6 times, proceed
with step 3. If it’s flashing some
other red status code, refer to
Table 29 to solve that problem
first. If it’s flashing green, the
module probably is not required
in the configuration. If it’s not on
or steady, cycle power to the
scanner.

3. Make sure the module is the

correct one for the
configuration.

4. Remove the module and check

for a bent pin, then reinsert the
module

5. Replace the module
6. Remove other modules and

replace one at a time until the
problem reoccurs. Most likely the
last module inserted needs to be
replaced.

7. Replace the rack.

All
modules

2

HW/SW
Key

The software
residing on the
module does
not match the
module type.
This diagnostic
should only
result in the
factory.

Replace module

DI and
Relay
DO and
DC DO

174

Chapter 8 - Diagnostics and Troubleshooting

«
...
172
173
174
175
176
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов