Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 153

153

n

Use suppression devices for additional noise protection. The
suppression devices can be added at the external source.
Appropriate suppression devices are commercially available.

Grounding wires for routing

Wires that carry relatively high electrical energy can produce
unwanted noise in wires that transmit signals of relatively low energy,
particularly when they are placed parallel in long wiring runs.

Collect and bundle wires of similar type, and route the bundle
separate from bundles of other types. The following table provides
suggested guidelines for grouping wires.

Table 6-2: Guidelines for grouping wires

Wire Group

Wire Functions

High voltage (>50 Vdc/VAC)

AC Line power wiring

Signal (<15 Vdc)

Analog signal wire, such as:

Low voltage (<50 Vdc/VAC)

Low voltage alarm relay output wiring

Wiring and cabling distance guidelines

Two network topologies are supported in I/O network: Ring and Star.

n

For Ethernet connections, cable length must be less than 100 m.
The use of Ethernet cables in excess of 100 meters and/or devices
other than recommended switches will cause transmission delays
on the I/O link which could have adverse effects on CPM
performance.

ATTENTION: Shielded Ethernet cables are required for I/O
link.

n

For greater than 100 m, a fiber optic cable is recommended with a
fiber switch or fiber optic converter.

n

If a multi-mode fiber optic cable connects to a MOXA unmanaged
Ethernet Switch or similar devices, the distance of the cable is up
to 5km. See

Fiber Optics Recommendations

section for more

information.

«
...
151
152
153
154
155
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов