Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 13

CHAPTER

2

OVERVIEW

Make sure all the hardware modules used in the system are installed
with the right firmware version and the engineering station has the
latest ControlEdge Builder. You can find the firmware and software
updates on http://www.honeywellprocess.com with valid credentials.

If the equipment is not used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.

ControlEdge 900 hardware components can be deployed in two
distinct types of control systems.

n

The ControlEdge Programmable Logic Controller (PLC)

n

The ControlEdge Unit Operations Controller (UOC)

For Control Processor Module (CPM), both the UOC and PLC use it
but with different firmware loaded.

ControlEdge PLC can be deployed standalone or with a SCADA
system including Experion PKS. Within Experion, ControlEdge PLC
can also communicate in a peer relationship to the DCS controllers
such as C300 and ContorlEdge UOC.

ControlEdge UOC is a DCS controller always deployed within
Experion PKS.

This document has been divided into three major sections.

n

ControlEdge PLC

- contains details specific to PLC.

n

ControlEdge UOC

- contains details specific to UOC.

n

ControlEdge 900 common reference information

and other

chapters- contains details applicable to ControlEdge platform,
both PLC and UOC.

How to Use this Guide

The following table outlines the tasks involved in planning and
installing a Honeywell ControlEdge 900 Controller. The links provided
will navigate the user through those tasks.

13

«
...
11
12
13
14
15
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов