Honeywell CGW-MB Скачать руководство пользователя страница 74

Страница: 74 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

CGW-MB Active Event Code

Modbus Communications

7.29 CGW-MB Active Event Code

All events are mapped into Modbus event categories which are stored in the Modbus
register.

0x0A

Unit ID specified in the request packet is not configured
for monitoring.

CLSS Gateway
mainboard path
failed

0x0B

FACP is off line or there is a communication problem on
the panel and/or NFN.

CLSS Gateway
mainboard
target failed

Table 7.37: Exception Codes

Table 7.38: Event Type Categories

Event

Modbus

Register

Value

No Active Status (see note)

00H

Mass Notification Alarm, High Priority

05H

Fire Alarm

10H

Security Alarm (Life)

11H

Critical Process Alarm (Life)

12H

Medical Emergency (Life)

13H

CO Alarm

14H

Mass Notification Alarm, Low Priority

15H

Security Alarm (Property)

20H

Critical Process (Property)

21H

Mass Notification Supervisory, High Priority

25H

Supervisory Signal (Guard’s Tour)

30H

Supervisory Signal (Equipment)

40H

Mass Notification Supervisory, Low Priority

45H

Disabled Alarm (AFP2800 Panel Only)

52H

Disabled Active (AFP2800 Panel Only)

55H

Non-Fire Activation

71H

Non-Fire Activation (no acknowledgment
required)

72H

CO Alarm & Fire Alarm

EAH

CO Supervisory

EBH

CO Supervisory & Photo Supervisory

ECH

CO Supervisory & Fire Alarm

EDH

CO Alarm & Photo Supervisory

EEH

Device Not Present

FFH

For Gamewell-FCI

General Alarm

18H

Gas Alarm

22H

CO Supervisory

42H

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 74 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: